Home > Parts > Vanagon 80-92 > Axle, Front > Syncro Driveline
We found 8 results matching your criteria.
Sort By:
Page of 1
Transmission Mount Washer 86-92 Vanagon Syncro CV Boot Kit - Front Inner - Syncro Vanagon CV Boot Kit - Front Outer - Vanagon Syncro (4WD)
This reproduction stainless steel washer, part number N 903 371 02, is used to secure front differential, and transmission mounts found on 86-92 Vanagon Syncro models.

Differential - 5 needed
Transmission - 4 needed

Fits 1986, 1987, 1988, 1989, 1990, 1991, and 1992 models. 		This German-made c.v. boot kit, part number 251 498 201A, is for the front inner joint on every Syncro (4wd) Vanagon. It fits 1986, 1987, 1988, 1989, 1990, 1991 and 1992 models.

1 needed per shaft - 2 total
 		This c.v. boot kit, part number 251 498 203F, is for the front outer joint on every Syncro (4WD) Vanagon. It fits 1986, 1987, 1988, 1989, 1990, 1991 and 1992 models.

1 needed per shaft - 2 total
Front Wheel Seal - Vanagon Syncro Transmission Mount Washer 86-92 Vanagon Syncro CV Joint Spacer Vanagon Syncro Front Inner
This seal, part number 251 407 629, is pressed into the suspension upright (spindle) on both sides of the wheel bearing to protect it from dirt and water on every Vanagon Syncro (4wd). It fits 1986, 1987, 1988, 1989, 1990, 1991 and 1992 models.

2 needed per side - 4 total 		This reproduction delrin washer, part number 251 199 399, sandwiches the front sub-frame and the transmission front brackets to support the rubber transmission mounts found in 86-92 Vanagon Syncro models.

Front differential - 4 needed
Transmission - 4 needed

Fits 1986, 1987, 1988, 1989, 1990, 1991, and 1992 models 		This reproduction CV joint spacer fits between the the front differential output flange and the inner cv joint on every 96-92 Vanagon Syncro.

2 needed
Locking Differential Selector Shaft Bushing Vanagon Syncro 86-92 CV Joint/Boot/Hardware Package - 944 For Lifted/Off-road Use - Syncro Inner
This stainless steel reproduction bushing is used on the transmission and front differential housing to support the locker selector shaft on 86-92 Vanagon Syncro models with locking differentials.

1 needed

It fits 1986, 1987, 1988, 1989, 1990, 1991, and 1992 models 		This Syncro Inner CV kit, part number BLOFFROADCVJOINTPACKAGESYNCROI, contains all the same parts and hardware we use here in the shop for a lifted or off-road Vanagon Syncro inner joint if you are purchasing a set for the rears - Porsche 944 CV joints, off-road/lifted CV boots, grease, the correct CV bolts and schnorr serrated washers. For the stock Vanagon CV kit, see item BLCVJOINTPACKAGE.

1 needed

It fits 1986, 1987, 1988, 1989, 1990, 1991 and 1992 models.

Installation note:
Put the flanges in to the large end of the boot before installing the bolts. We supply thin metal zip ties to secure the boot on the flange due to tight clearances. Be sure to fit the clasp of the zip tie between the bolt holes of the flange so it doesn't interfere with bolts. The bolts fit snugly against the zip tie, you may need to put the washers in place before pushing the bolts through the flanges. Due to the thickness of the the flange there is no need to reuse your cv spacer plates.